Before using your Dripro Waterproof Case, please check that it got to you in perfect condition. Seal something worthless inside, and then submerge in water. see below for instruction.

1. Seal something worthless (such as napkin) into the case	2. Hold the left side ofthe ziplock	3. Slide all ziplocks to the right and hear the snapping sound ensure the zippers are closed	4. Fold along the zipper crease
5. Close the cover with velcro closure	6. Submerge in a basin	7. A few air bubbles may escape from the plastic flap, this is OK, water can get into the flap without getting into the case. After few minutes, take out the case from the water and check the napkin, it should be dry. As a result, this waterproof case is in perfect conditions.	8. If a stream of bubbles escapes when you squeeze it there may be a problem. Take out the case and check the napkin, if the napkin get wet which means this waterproof case is damaged. Please stop useing this waterproof case.

Take care of your waterproof case:

Examine your case before each use to make sure it's not visibly damaged to be safe you should always do the Bubble Test. Before opening, always shake any water from the plastic flap. Otherwise it could get into the case when you open it. Wash in soapy water and then rise with fresh water, especially after regular contact with chlorinated or salt water, or with sun creams. Do not use bleach, alcohol or proprietary cleaners.

Waterproof test standard:

Our waterproof cases are 100% waterproof and submeribe. They are certified by SGS for international waterproof test (IPX), compliance with the highest level IPX8 which means it can submerged into water up to 10 meters in 30 mintues.

Level	Protected against	Testing for	Details
8	Immersion beyond 1 m	The equipment is suitable for continuous immersion in water under conditions which shall be specified by the manufacturer. Normally, this will mean that the equipment is hermetically sealed. However, with certain types of equipment, it can mean that water can enter but only in such a manner that it produces no harmful effects.	Test duration: continuous immersion in water Immersion at depth of 10m
7	Immersion up to 1 m	Ingress of water in harmful quantity shall not be possible when the enclosure is immersed in water under defined conditions of pressure and time (up to 1 m of submersion).	Test duration: 30 minutes Immersion at depth of at least 1 m measured at bottom of device, and at least 15 cm measured at top of device
6	Powerful water jets	Water projected in powerful jets (12.5 mm nozzle) against the enclosure from any direction shall have no harmful effects.	Test duration: at least 3 minutes Water volume: 100 litres per minute Pressure: 100 kPa at distance of 3 m
5	Water jets	Water projected by a nozzle (6.3 mm) against enclosure from any direction shall have no harmful effects.	Test duration: at least 3 minutes Water volume: 12.5 litres per minute Pressure: 30 kPa at distance of 3 m
4	Splashing water	Water splashing against the enclosure from any direction shall have no harmful effect.	Test duration: 5 minutes Water volume: 10 litres per minute Pressure: 80–100 kPa
3	Spraying water	Water falling as a spray at any angle up to 60° from the vertical shall have no harmful effect.	Test duration: 5 minutes Water volume: 0.7 litres per minute Pressure: 80–100 kPa
2	Dripping water when tilted up to 15°	Vertically dripping water shall have no harmful effect when the enclosure is tilted at an angle up to 15° from its normal position.	Test duration: 10 minutes Water equivalent to 3 mm rainfall per minute
1	Dripping water	Dripping water (vertically falling drops) shall have no harmful effect.	Test duration: 10 minutes Water equivalent to 1 mm rainfall per minute
0	Not protected	—	—